Approx. Rs 7,500 / Unit Get Latest Price
Light Dependant Resister (LDR) Trainer Model: UITM- 08
Our Light Dependant Resister (LDR) Trainer Model: UITM- 08 is an experimental setup to study the characteristics of LDR and its behavior with respect to light intensity. These are fixed to movable rod inside a metal tube where a bulb is fixed at the other end.
The whole setup is mounted on a base where the experiment can be conducted
As a study project the indicator is settable to display the distance moved by the LDR with respect to the light source
The instrument is calibrated to reach distance to a max of 50mm
Scale is provided to verify the display reading
The intensity of the light can be varied by varying the excitation voltage to the bulb and also by moving the LDR near and away from the bulb
LDR: 10 K ohms
Bulb: 12V bulb
Display: 31/2 Digit display to read up to 30mm with variable
Voltage source to the bulb
Displacement: Max 30mm
Approx. Rs 11,000 / Unit(s) Get Latest Price
Speed Measurement Trainer (Model: UITM- 07)
We offer an extensive range of Speed Measurement Trainer (Model: UITM- 07), which comprises of a DC Motor, which is fixed rigidly on a strong metal stand. It is equipped with four digit digital tachometer is provided along with the above setup which is calibrated to read the speed up to 1500 RPM.
The system comprises of a small 12V DC Motor, which is fixed rigidly on a strong metal stand
The motor runs by 12V DC supply.
Potentiometer is used to controls the speed of the motor
Two tone wheels of sixty teeth are fixed to the motor shaft, one is of MS material and the other is of copper
Magnetic pickup speed sensor is fixed at a distance of 2 to 2.5mm away from the teeth of the MS tone wheel, which senses the speed
A Photoreflective sensor id mounted across the topper tone wheel so that the wheel rotates between the sensor and the infra red LED source
Four digit digital tachometer is provided along with the above setup which is calibrated to read the speed up to 1500 RPM
The meter will accept the signals from both magnetic pickup and photo sensor one at a time
Selection switch is provided to select the sensor on which the experiment has to be conducted
Motor Capacity: 12V DC Motor.
Max. Motor Speed: 1500 RPM (approx.)
Motor input Supply: 12V DC.
Motor Speed Control: Using POT.
Tone Wheel: MS Gear wheel of 60Teeth, Copper wheel with 60 slots
Sensor: Non- Contact Magnetic Pickup & Opto-coupler IC
Display: Digital Seven segment Red LED display to read upto 9999 counts
Power Supply: 230V 50Hz.
Accessories: Instruction manual
Approx. Rs 32,000 / Unit(s) Get Latest Price
Level Measurement Trainer Model - UITM -12
Our organization is engaged in offering Level Measurement Trainer Model – UITM -12, which is a unique model specially designed to demonstrate the method and application of load cell to measure water level in a tank. This is provided with a drain valve to release the water to the source tank
The set up:
The system comprises of a acrylic tank of capacity 10 liters fitted with a scale to measure the Level of water
The tank is provided with a drain valve to release the water to the source tank
The beam type load cell of capacity 1Kg is mounted on the acrylic cover on top of the measuring tank
A metallic tube is suspended from the load cell till the bottom of the measuring tank
The Load Cell is connected to digital Load indicator
The instrument is calibrated to read the level in terms of centimeter
In the front panel of the instrument zero pot is provided by which the display can be made zero level
Sensor: LOAD CELL with rod suspended
Measuring Tank: Acrylic tank of 60cms length
Measuring Range: 50 cms
Water Pump: FHP vertical pump
Source Tank: Metallic tank with EPI coating
Display: 3.5 digit seven segment LED display
Excitation: 10 V DC
Tare: Front panel Zero adjustment through Potentiometer
Calibration: Front panel cal adjustment through Potentiometer
Power Supply: 230 V +/- 10% 50 Hz
Cabinet: Powder coated metal cabinet with inbuilt source tank of dimension 500 X 500 X 450 (L X B X H)
*Your information is safe with us.
Approx. Rs 32,000 / Unit(s) Get Latest Price
PLC Trainer Model:DI-6DO
We are engaged in offering PLC Trainer that is applicable in industrial PLC, SCADA, logic control(PLC) and data acquisition. The trainer is ABB and Delta make, it receives 8 digital inputs and provides 6 digital outputs. This easy to install equipment is easy to operate and low in maintenance. It finds usage in electronics lab, measurement lab, material testing lab, instrumentation lab and Transducers labs of various engineering branches.
NOTE: Range between Rs 32000 to 45000
Approx. Rs 9,000 / Unit(s) Get Latest Price
Strain Measurement Trainer (Model: UITM-01)
We are engaged in offering Strain Measurement Trainer (Model: UITM- 01), which comprises of stainless steel beam firmly fixed at one end and the other end is free to load. Our range is available in various dimensions, resolution and power supply’s as per the clients specific requirements. The main features of the strain indicator are front panel strain gauge bridge balancing with the help of potentiometer and the whole system is self-contained with all accessories included.
The fixture is mounted on a base plate rigidly
Four strain gauges are bonded on the beam and are connected in the form of whetstone bridge
Terminals are brought out through five different color sockets to connect easily
A pan & weight up to 1 Kg in steps of 100gms will be supplied for loading the cantilever beam
Digital strain indicator will be supplied along with the cantilever beam setup to measure the micro strain
The instrument comprises of inbuilt power supply for self and also for the strain gauge
excitation, strain gauge signal conditioner and amplifier and 31/2 digit analog to digital converter
The main features of the strain indicator are front panel strain gauge Bridge balancing with the help of potentiometer
The whole system is self-contained with all accessories included
The instrument is enclosed in a tapered fiberglass box and all necessary test points are brought out with schematic circuitry for understanding the working of the instrument
The instrument operates on 230V power supply
Beam Dimension: Length 300 mm, width 28 mm and thickness 2.5
Material: Stainless steel
Weights: 1 Kg, in steps of 100gms
Strain gauge: 350 ohms resistance, gauge factor 2 to 2.1
Display: 31/2 digit seven segment led display
Connection: 4 core shielded cable
Resolution: 1 micro strain
Excitation: 10 to 12 V DC